Maneater HDPE Molds

Set of 6 silicone inserts for the "DINOBONE - MINI COMBO CASTING SYSTEM".  These inserts fit chambers measuring 4.50" x .75" x 1.0".

The stoppers will accommodate tubes 7mm - 27/64" in diameter.  

Single Pair of silicone inserts for the "DINOBONE - MINI COMBO CASTING SYSTEM".  These inserts fit chambers measuring 4.50" x .75" x 1.0".

The stoppers will accommodate tubes 7mm - 27/64" in diameter.  

Set of 2 silicone inserts for the DINOBONE - COMBO CASTING SYSTEM.  These inserts fit chambers measuring 5.25" x .84375" x 1.0".

The large stoppers will accommodate tubes 27/64" - 13.2mm in diameter. 

Set of 2 silicone inserts for the "DINOBONE - COMBO CASTING SYSTEM".  These inserts fit chambers measuring 5.25" x .84375" x 1.0".

These blocks are designed to all for casting shorter than the full length blanks. 

Set of 2 silicone inserts for the "DINOBONE - COMBO CASTING SYSTEM".  These inserts fit chambers measuring 5.25" x .84375" x 1.0".

The small stoppers will accommodate tubes 7mm - 27/64" in diameter. 

Special Offer: 40% Off Due to Manufacturing Error

NOT FOR USE WITH LABEL TUBE CASTING

These DinoBone 1 Mold Body molds are offered at a 40% discount due to a manufacturing error where the casting slots were cut 0.5mm too wide, making them incompatible with our tube casting plugs. They are ideal for single blank casting with solid resin or hybrid resin, producing high-quality pen blanks.

To easily distinguish these SECONDS from properly manufactured molds, the ears on the ends have been flattened.

Crafted from durable HDPE (High-Density Polyethylene), these semi-permanent molds resist warping and cracking, outperforming traditional silicone molds. Their stackable design eliminates the need for a casting rack, streamlining your workspace. Demolding is simple—remove the suction plugs, flip the mold, and tap the ends on your workbench to release the blanks.

Mold Specifications:

- Dimensions: 7" x 2.25" x 1.60"
- Casting Chambers: Single chamber, 5.25" x 0.863" x 1.0"
- Material: Milled HDPE for durability
- Features: Stackable, reusable, easy demolding, flattened ears for identification

Usage Instructions:

Apply a release agent, such as Maneater Wax Mold Release or Maneater Silicone Mold Release, to the chambers and rubber plugs to prevent resin buildup. Ensure full coverage and let it dry before pouring resin. After curing, use a rubberized dead blow hammer to lightly tap the mold’s bottom and sides. Flip the mold and tap the ends on your workbench to release the blanks. Alumilite and polyester resin blanks release effortlessly, while epoxy blanks may require extra taps or a blast of air from a rubberized nozzle.

Why Buy These Seconds?

Despite the oversized slots, these molds are a cost-effective solution for single blank casting. Their robust construction, innovative stackable design, and discounted price make them an excellent choice for crafting stunning pen blanks.

Note:

These molds are NOT compatible with any tube casting plugs due to the 0.5mm oversized slots. The flattened ears on the ends identify them as SECONDS. Trim blanks on a table saw for precise squaring, if needed.

Get these high-quality molds at a 40% discount while supplies last!

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold body has overall dimensions of 13.25" x 6.50" x 1.60" with TEN casting chambers, each measuring 5.25" x .84375" x 1.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold system has overall dimensions of 7.25" x 3.75" x 1.60" with two casting chambers, each measuring 5.25" x .84375" x 1.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

Includes four large stopper silicone inserts and four small stopper silicone inserts!  The small stoppers will accommodate tubes 7mm - 27/64" in diameter.  The large stoppers will accommodate tubes 27/64" - 13.2mm. 

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers and on the silicone inserts, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold body has overall dimensions of 7.25" x 3.75" x 1.60" with two casting chambers, each measuring 5.25" x .84375" x 1.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Special Offer: 40% Off Due to Manufacturing Error

NOT FOR USE WITH LABEL TUBE CASTING

These DinoBone 2-Mold Body molds are offered at a 40% discount due to a manufacturing error where the casting slots were cut 0.5mm too wide, making them incompatible with our tube casting plugs. They are ideal for single blank casting with solid resin or hybrid resin, producing high-quality pen blanks.

To easily distinguish these SECONDS from properly manufactured molds, the ears on the ends have been flattened.

Crafted from durable HDPE (High-Density Polyethylene), these semi-permanent molds resist warping and cracking, outperforming traditional silicone molds. Their stackable design eliminates the need for a casting rack, streamlining your workspace. Demolding is simple—remove the suction plugs, flip the mold, and tap the ends on your workbench to release the blanks.

Mold Specifications:

- Dimensions: 7" x 3.75" x 1.60"
- Casting Chambers: Two chambers, each 5.25" x 0.863" x 1.0"
- Material: Milled HDPE for durability
- Features: Stackable, reusable, easy demolding, flattened ears for identification

Usage Instructions:

Apply a release agent, such as Maneater Wax Mold Release or Maneater Silicone Mold Release, to the chambers and rubber plugs to prevent resin buildup. Ensure full coverage and let it dry before pouring resin. After curing, use a rubberized dead blow hammer to lightly tap the mold’s bottom and sides. Flip the mold and tap the ends on your workbench to release the blanks. Alumilite and polyester resin blanks release effortlessly, while epoxy blanks may require extra taps or a blast of air from a rubberized nozzle.

Why Buy These Seconds?

Despite the oversized slots, these molds are a cost-effective solution for single blank casting. Their robust construction, innovative stackable design, and discounted price make them an excellent choice for crafting stunning pen blanks.

Note:

These molds are NOT compatible with any tube casting plugs due to the 0.5mm oversized slots. The flattened ears on the ends identify them as SECONDS. Trim blanks on a table saw for precise squaring, if needed.

Get these high-quality molds at a 40% discount while supplies last!

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold system has overall dimensions of 7.25" x 5.25" x 1.60" with three casting chambers, each measuring 5.25" x .84375" x 1.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

Includes six large stopper silicone inserts and six small stopper silicone inserts!  The small stoppers will accommodate tubes 7mm - 27/64" in diameter.  The large stoppers will accommodate tubes 27/64" - 13.2mm. 

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers and on the silicone inserts, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold body has overall dimensions of 7.25" x 5.25" x 1.60" with three casting chambers, each measuring 5.25" x .84375" x 1.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Special Offer: 40% Off Due to Manufacturing Error

NOT FOR USE WITH LABEL TUBE CASTING

These DinoBone 1 Mold Body molds are offered at a 40% discount due to a manufacturing error where the casting slots were cut 0.5mm too wide, making them incompatible with our tube casting plugs. They are ideal for single blank casting with solid resin or hybrid resin, producing high-quality pen blanks.

To easily distinguish these SECONDS from properly manufactured molds, the ears on the ends have been flattened.

Crafted from durable HDPE (High-Density Polyethylene), these semi-permanent molds resist warping and cracking, outperforming traditional silicone molds. Their stackable design eliminates the need for a casting rack, streamlining your workspace. Demolding is simple—remove the suction plugs, flip the mold, and tap the ends on your workbench to release the blanks.

Mold Specifications:

- Dimensions: 7" x 5.25" x 1.60"
- Casting Chambers: Three chambers, 5.25" x 0.863" x 1.0"
- Material: Milled HDPE for durability
- Features: Stackable, reusable, easy demolding, flattened ears for identification

Usage Instructions:

Apply a release agent, such as Maneater Wax Mold Release or Maneater Silicone Mold Release, to the chambers and rubber plugs to prevent resin buildup. Ensure full coverage and let it dry before pouring resin. After curing, use a rubberized dead blow hammer to lightly tap the mold’s bottom and sides. Flip the mold and tap the ends on your workbench to release the blanks. Alumilite and polyester resin blanks release effortlessly, while epoxy blanks may require extra taps or a blast of air from a rubberized nozzle.

Why Buy These Seconds?

Despite the oversized slots, these molds are a cost-effective solution for single blank casting. Their robust construction, innovative stackable design, and discounted price make them an excellent choice for crafting stunning pen blanks.

Note:

These molds are NOT compatible with any tube casting plugs due to the 0.5mm oversized slots. The flattened ears on the ends identify them as SECONDS. Trim blanks on a table saw for precise squaring, if needed.

Get these high-quality molds at a 40% discount while supplies last!

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold system has overall dimensions of 7.25" x 6.75" x 1.60" with four casting chambers, each measuring 5.25" x .84375" x 1.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

Includes eight large stopper silicone inserts and eight small stopper silicone inserts!  The small stoppers will accommodate tubes 7mm - 27/64" in diameter.  The large stoppers will accommodate tubes 27/64" - 13.2mm. 

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers and on the silicone inserts, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold body has overall dimensions of 7.25" x 6.75" x 1.60" with four casting chambers, each measuring 5.25" x .84375" x 1.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold body has overall dimensions of 11.25" x 7.25" x 1.60" with EIGHT casting chambers, each measuring 6" x .84375" x 1.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold system has overall dimensions of 6.25" x 4.875" x 1.60" with three casting chambers, each measuring 4.5" x .75" x 1.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

Includes six small stopper silicone inserts!  The stoppers will accommodate tubes 7mm - 27/64" in diameter.

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers and on the silicone inserts, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold body has overall dimensions of 6.25" x 4.875" x 1.60" with three casting chambers, each measuring 4.5" x .75" x 1.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold system has overall dimensions of 7.25" x 3.75" x 1.60" with single casting chamber, each measuring 5.25" x .84375" x 1.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

 Includes four large stopper silicone inserts and four small stopper silicone inserts!  The small stoppers will accommodate tubes 7mm - 27/64" in diameter.  The large stoppers will accommodate tubes 27/64" - 13.2mm. 

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers and on the silicone inserts, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

If you enjoy clear casting labels, watch parts, skins, hybrids, etc. and are looking for a semi-permanent solution for tube-in casting, then the new Maneater Crafts “DogBone” tube-in casting mold is for you! It’s a single mold solution that is super simple to use and will work with the majority of turning kits on the market (not to exceed tubes over 12.5mm in diameter). It’s literally a one mold fits all solution!! That includes most pen kits, seam rippers, razors and even darts!

What makes the DogBone so special? To start, it is milled from solid HDPE and is virtually indestructible. It won’t warp or crack like silicone molds. It features two 5.5” x .75” chambers and two sets of silicone inserts. One set has small stoppers for 7mm - 3/8” tubes. The other set has stoppers for 3/8” - 12.5mm tubes. The inserts are replaceable at a cost of $8 per set. The mold body should last for years if properly cared for.

What else is special about the DogBone? Well, the unique design allows the molds to stack one on top of the other. They will self-align with the included rubber feet and if pressure casting in a 2.5 gal pot, you can stack them up to six molds high and two stacks side by side. That gives you the ability to cast up to 24 blanks at a time!! And best of all, no mold caddy it needed!! That makes this mold ideal for hobby casters and volume casters alike!

The DogBone is strictly intended for tube-in casting since the chambers don’t include bottom plugs to assist with blank removal. If you are interested in casting full chamber blanks then please try one of the other Maneater molds. All of the usual casting resins will work great, including Royal Palm, Alumilite and PR (polyester resin).

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers and on the silicone inserts, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

.