Products

If you enjoy clear casting labels, watch parts, skins, hybrids, etc. and are looking for a semi-permanent solution for tube-in casting, then the new Maneater Crafts “DogBone” tube-in casting mold is for you! It’s a single mold solution that is super simple to use and will work with the majority of turning kits on the market (not to exceed tubes over 12.5mm in diameter). It’s literally a one mold fits all solution!! That includes most pen kits, seam rippers, razors and even darts!

What makes the DogBone so special? To start, it is milled from solid HDPE and is virtually indestructible. It won’t warp or crack like silicone molds. It features two 5.5” x .75” chambers and two sets of silicone inserts. One set has small stoppers for 7mm - 3/8” tubes. The other set has stoppers for 3/8” - 12.5mm tubes. The inserts are replaceable at a cost of $8 per set. The mold body should last for years if properly cared for.

What else is special about the DogBone? Well, the unique design allows the molds to stack one on top of the other. They will self-align with the included rubber feet and if pressure casting in a 2.5 gal pot, you can stack them up to six molds high and two stacks side by side. That gives you the ability to cast up to 24 blanks at a time!! And best of all, no mold caddy it needed!! That makes this mold ideal for hobby casters and volume casters alike!

The DogBone is strictly intended for tube-in casting since the chambers don’t include bottom plugs to assist with blank removal. If you are interested in casting full chamber blanks then please try one of the other Maneater molds. All of the usual casting resins will work great, including Royal Palm, Alumilite and PR (polyester resin).

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers and on the silicone inserts, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

.

Special Offer: 40% Off Due to Manufacturing Error

NOT FOR USE WITH LABEL TUBE CASTING

These Dogbone 1 Mold Body molds are offered at a 40% discount due to a manufacturing error where the casting slots were cut 0.5mm too wide, making them incompatible with our tube casting plugs. They are ideal for single blank casting with solid resin or hybrid resin, producing high-quality pen blanks.

To easily distinguish these SECONDS from properly manufactured molds, the ears on the ends have been flattened.

Crafted from durable HDPE (High-Density Polyethylene), these semi-permanent molds resist warping and cracking, outperforming traditional silicone molds. Their stackable design eliminates the need for a casting rack, streamlining your workspace. Demolding is simple—remove the suction plugs, flip the mold, and tap the ends on your workbench to release the blanks.

Mold Specifications:

- Dimensions: 6.5" x 3.25" x 1.25"
- Casting Chambers: Single chamber, 5.5" x 0.77" x 1.0"
- Material: Milled HDPE for durability
- Features: Stackable, reusable, easy demolding, flattened ears for identification

Usage Instructions:

Apply a release agent, such as Maneater Wax Mold Release or Maneater Silicone Mold Release, to the chambers and rubber plugs to prevent resin buildup. Ensure full coverage and let it dry before pouring resin. After curing, use a rubberized dead blow hammer to lightly tap the mold’s bottom and sides. Flip the mold and tap the ends on your workbench to release the blanks. Alumilite and polyester resin blanks release effortlessly, while epoxy blanks may require extra taps or a blast of air from a rubberized nozzle.

Why Buy These Seconds?

Despite the oversized slots, these molds are a cost-effective solution for single blank casting. Their robust construction, innovative stackable design, and discounted price make them an excellent choice for crafting stunning pen blanks.

Note:

These molds are not compatible with tube casting plugs due to the 0.5mm oversized slots and are designed exclusively for single blank casting. The flattened ears on the ends clearly identify them as SECONDS. For precise squaring, trim blanks on a table saw if needed. The bottom hole slot plugs, designed for the DinoBone mold series, are compatible but require adaptation of their usage for the DogBone mold. Ensure the silicone slot plugs are trimmed to fit flush with the DinoBone mold base to prevent indentations in your blanks, but they need to be pulled back slightly as shown below for the DogBone Molds.

Get these high-quality molds at a 40% discount while supplies last!

Special Offer: 40% Off Due to Manufacturing Error

NOT FOR USE WITH LABEL TUBE CASTING

These DogBone 1 Mold Body molds are offered at a 40% discount due to a manufacturing error where the casting slots were cut 0.5mm too wide, making them incompatible with our tube casting plugs. They are ideal for single blank casting with solid resin or hybrid resin, producing high-quality pen blanks.

To easily distinguish these SECONDS from properly manufactured molds, the ears on the ends have been flattened.

Crafted from durable HDPE (High-Density Polyethylene), these semi-permanent molds resist warping and cracking, outperforming traditional silicone molds. Their stackable design eliminates the need for a casting rack, streamlining your workspace. Demolding is simple—remove the suction plugs, flip the mold, and tap the ends on your workbench to release the blanks.

Mold Specifications:

- Dimensions: 6.5" x 3.25" x 1.25"
- Casting Chambers: Single chamber, 5.5" x 0.77" x 1.0"
- Material: Milled HDPE for durability
- Features: Stackable, reusable, easy demolding, flattened ears for identification

Usage Instructions:

Apply a release agent, such as Maneater Wax Mold Release or Maneater Silicone Mold Release, to the chambers and rubber plugs to prevent resin buildup. Ensure full coverage and let it dry before pouring resin. After curing, use a rubberized dead blow hammer to lightly tap the mold’s bottom and sides. Flip the mold and tap the ends on your workbench to release the blanks. Alumilite and polyester resin blanks release effortlessly, while epoxy blanks may require extra taps or a blast of air from a rubberized nozzle.

Why Buy These Seconds?

Despite the oversized slots, these molds are a cost-effective solution for single blank casting. Their robust construction, innovative stackable design, and discounted price make them an excellent choice for crafting stunning pen blanks.

Note:

These molds are not compatible with tube casting plugs due to the 0.5mm oversized slots and are designed exclusively for single blank casting. The flattened ears on the ends clearly identify them as SECONDS. For precise squaring, trim blanks on a table saw if needed. The bottom hole slot plugs, designed for the DinoBone mold series, are compatible but require adaptation of their usage for the DogBone mold. Ensure the silicone slot plugs are trimmed to fit flush with the DinoBone mold base to prevent indentations in your blanks, but they need to be pulled back slightly as shown below for the DogBone Molds.

Get these high-quality molds at a 40% discount while supplies last!

High-capacity 8-slot HDPE casting mold designed specifically for DogBone label casting plugs. Cast two tubes per slot for Jr. Gent, Sierra Clone, Bolt Action, and most other common pen kits.

Product Description (copy/paste ready):

If you love label casting with dogbone plugs and want serious production capacity, this 8-slot tube-in casting mold is the perfect upgrade. Designed to accommodate our dogbone label casting plugs, it lets you cast two tubes per slot for most popular pen kits (Jr. Gent, Sierra Clone, Bolt Action, and more).

Each slot measures 7" long, giving you plenty of room for full-length blanks with excellent results. The mold is precision-milled from durable, virtually indestructible HDPE — no warping or cracking like flexible silicone molds.

Key Features:

• 8 slots — cast up to 16 tubes (2 per slot) in a single pour
• 7" slot length — ideal for standard pen blanks
• Compatible with DogBone label casting plugs
• Works with all common tube sizes (Jr. Gent, Sierra Clone, Bolt Action, etc.)
• Designed for pressure casting in 5-gallon or larger resin pressure pots (will NOT fit in 2.5-gallon pots)
• Robust construction built for repeated use

This mold is strictly intended for tube-in / label casting. All standard casting resins perform great, including JB Royal Epoxy, Alumilite urethane, other epoxy resins, and polyester resins.

Important Notes:

• A good release agent is required. We highly recommend applying it thoroughly to the chambers and any plugs/inserts before pouring.
• For easiest demolding, use a rubberized dead blow hammer after full cure. Tap the bottom and sides, then flip and tap the ends on your workbench.
• Alumilite and polyester blanks typically release very easily. Epoxy blanks may need a few extra taps or a blast of compressed air.

Usage Tips:

• Always pressure cast when possible for bubble-free results.
• Test your setup in your pressure pot before full production runs.
• Clean the mold thoroughly after each use for maximum lifespan.

This heavy-duty mold is perfect for serious hobbyists and volume casters who want reliable, repeatable results with DogBone label casting.

If you enjoy clear casting labels, watch parts, skins, hybrids, etc. and are looking for a semi-permanent solution for tube-in casting, then the new Maneater Crafts “DogBone” tube-in casting mold is for you! It’s a single mold solution that is super simple to use and will work with the majority of turning kits on the market (not to exceed tubes over 12.5mm in diameter). It’s literally a one mold fits all solution!! That includes most pen kits, seam rippers, razors and even darts! 

What makes the DogBone so special? To start, it is milled from solid HDPE and is virtually indestructible. It won’t warp or crack like silicone molds. It features SIXTEEN 2.5” x .75” chambers. Perfect for casting short blanks. Total mold size approximately is 9" x 7.25" x 1.25"

What else is special about the DogBone? Well, the unique design allows the molds to stack one on top of the other. They will self-align with the included rubber feet and if pressure casting in a 2.5 gal pot, you can stack them up to six molds high and two stacks side by side. That gives you the ability to cast up to 24 blanks at a time!! And best of all, no mold caddy it needed!! That makes this mold ideal for hobby casters and volume casters alike!

The DogBone is strictly intended for tube-in casting since the chambers don’t include bottom plugs to assist with blank removal. If you are interested in casting full chamber blanks then please try one of the other Maneater molds. All of the usual casting resins will work great, including Royal Palm, Alumilite and PR (polyester resin).

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers and on the silicone inserts, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

.

TWO Sets of FOUR silicone inserts for the "Dog Bone - Tube-In Casting Mold".  

One set of FOUR small stoppers for 7mm - 10mm tubes. The other set has FOUR large stoppers for 3/8” - 12.5mm tubes.

Set of FOUR LARGE silicone inserts for the "DogBone - Tube-In Casting Mold".  

One set if silicon inserts for 3/8” - 12.5mm tubes.

Set of four SMALL Silicone inserts for the "Dog Bone - Tube-In Casting Mold".  

Two pairs of small stoppers for 7mm - 10mm tubes.

If you enjoy clear casting labels, watch parts, skins, hybrids, etc. and are looking for a semi-permanent solution for tube-in casting, then the new Maneater Crafts “DogBone” tube-in casting mold is for you! It’s a single mold solution that is super simple to use and will work with the majority of turning kits on the market (not to exceed tubes over 12.5mm in diameter). It’s literally a one mold fits all solution!! That includes most pen kits, seam rippers, razors and even darts! 

What makes the DogBone so special? To start, it is milled from solid HDPE and is virtually indestructible. It won’t warp or crack like silicone molds. It features a single 5.5” x .75” chambers and two pair of silicone inserts. One pair has small stoppers for 7mm - 3/8” tubes. The other pair has stoppers for 3/8” - 12.5mm tubes. The inserts are replaceable at a cost of $8 per set. The mold body should last for years if properly cared for.

What else is special about the DogBone? Well, the unique design allows the molds to stack one on top of the other. They will self-align with the included rubber feet and if pressure casting in a 2.5 gal pot, you can stack them up to six molds high and two stacks side by side. That gives you the ability to cast up to 24 blanks at a time!! And best of all, no mold caddy it needed!! That makes this mold ideal for hobby casters and volume casters alike!

The DogBone is strictly intended for tube-in casting since the chambers don’t include bottom plugs to assist with blank removal. If you are interested in casting full chamber blanks then please try one of the other Maneater molds. All of the usual casting resins will work great, including Royal Palm, Alumilite and PR (polyester resin). 

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers and on the silicone inserts, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

 A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Sierra and Bolt embedded blanks with  Korean War and Vietnam era Douglas A-4 Sky Hawk Relic.

All blanks will come with one COA per blank.
COAs are 4" x 6" card stock with foil COA seal.

The Douglas A-4 Skyhawk is a lightweight, carrier-capable attack aircraft developed for the U.S. Navy and Marine Corps. Designed by Ed Heinemann of Douglas Aircraft Company, the Skyhawk first flew in 1954 and entered service in 1956. Known for its compact size and agility, the A-4 was affectionately nicknamed "Heinemann's Hot Rod" after its designer.

The A-4 Skyhawk was initially intended as a nuclear-capable bomber but quickly proved its versatility across various roles, including ground attack, close air support, and even as an adversary aircraft in training exercises. Its delta-wing design and absence of wingtip folding mechanisms allowed it to be exceptionally light, which contributed to its impressive speed and maneuverability.

Throughout its service, the Skyhawk saw extensive use in several conflicts, most notably during the Vietnam War. It was a reliable workhorse, performing critical bombing missions, close air support, and interdiction operations. The A-4 was also used by several foreign air forces, including those of Israel and Argentina, where it played key roles in their respective military operations.

The A-4’s simplicity and effectiveness led to its long service life, with some variants remaining in use well into the 21st century. Its durability and adaptability have cemented its place as one of the most successful attack aircraft in military aviation history.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax or Silicone Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Watch Part Steampunk Jr Cap. 

These blanks are 12.5mm and 10.5mm tube sets used with the common Jr Gent sized kits. These sports team blanks pair excellently with team color resin blanks. 

The list below is not a complete list, but it is a great starting point list to find your desired kit.

Wooden seat pen blanks!

Blanks are 3/4" x 3/4"

All blanks will come with one COA per blank. COAs are 4" x 6" card stock with silver foil embossed COA seal.

All blanks are cut as they are ordered.

------------------------------------------------------------

Ebbets Field was a Major League Baseball stadium in the Flatbush section of Brooklyn, New York. It is known mainly as the home of the Brooklyn Dodgers baseball team of the National League, from 1913 to 1957, but was also home to three National Football League teams in the 1920s. Ebbets Field was demolished in 1960 and replaced by apartment buildings.

Ebbets Field was one of several historic major league ballparks demolished in the 1960s, but more mythology and nostalgia surrounds the stadium and its demise than possibly any other defunct ballpark.

A great deal of history happened at Ebbets Field during its 45 years. Of the many teams that uprooted in the 1950s and 1960s, the Dodgers have probably had the largest number of public laments over their fans' heartbreak over losing their team. Several decades later, Roger Kahn's acclaimed book The Boys of Summer and Frank Sinatra's song "There Used to Be a Ballpark" mourned the loss of places like Ebbets Field, and of the attendant youthful innocence of fans and players alike. The story of Ebbets Field and the Brooklyn Dodgers' move to Los Angeles were also chronicled by historian Doris Kearns Goodwin, figured into the plot of the film Field of Dreams, and were featured in an entire episode of Ken Burns' public-television documentary Baseball, as well as a 2007 HBO documentary called Brooklyn Dodgers: Ghosts of Flatbush.

In 2006, the Dodgers matched the years they played at Ebbets Field with their years in Dodger Stadium. The New York Mets' duration in Shea Stadium (1964-2008) was the same as that of the Dodgers in Ebbets Field.

JB Royal Alumilite EMERALD CRYSTAL green resin blanks with suspended shredded resin cut-offs from the over-pour of other Alumilite and JB Royal resin blocks. The suspended material is a wild variety of mixes to form a kaleidoscope of colors.

Blank Sizes:

• 5" Long Blank  measures a minimum of 3/4" square
• 9" Kitless Blank measures 3/4" round
• 2-1/2" Stopper Blank  measures 1-1/2" round
• 5" Call Blank measures 1-1/2" round

You may find this to be opaque. We recommend back painting the blank after drilling. Using different colors for back painting will yield wildly different effects and results.

As with any suspended material blanks, there is the likely hood of tiny bubbles. These bubbles can easily be remedied with CA (cyanoacrylate) glue.

JB Royal Alumilite EMERALD GREEN resin blanks with suspended shredded resin cut-offs from the over-pour of other Alumilite and JB Royal resin blocks. The suspended material is a wild variety of mixes to form a kaleidoscope of colors.

Blank Sizes:

• 5" Long Blank  measures a minimum of 3/4" square
• 9" Kitless Blank measures 3/4" round
• 2-1/2" Stopper Blank  measures 1-1/2" round
• 5" Call Blank measures 1-1/2" round

You may find this to be opaque. We recommend back painting the blank after drilling. Using different colors for back painting will yield wildly different effects and results.

As with any suspended material blanks, there is the likely hood of tiny bubbles. These bubbles can easily be remedied with CA (cyanoacrylate) glue.

Military Service Branches
Engraved $10 each

No Engraving $5 each
Custom Engraving $25 each

You will need the lower half of a Sierra Vista Pen Kit or Wall Street III Pen Kit to complete this pen.

------------------------------------------------------------

Please allow for 2-3 weeks for custom order engraving. Custom image or text must be emailed to Stadium Pen Blanks.

The .50 Browning Machine Gun (.50 BMG, 12.7×99mm NATO and designated as the 50 Browning by the C.I.P.) is a cartridge developed for the Browning .50 caliber machine gun in the late 1910s, entering official service in 1921. Under STANAG 4383, it is a standard cartridge for NATO forces as well as many non-NATO countries. The cartridge itself has been made in many variants: multiple generations of regular ball, tracer, armor-piercing (AP), incendiary, and saboted sub-caliber rounds. The rounds intended for machine guns are made into a continuous belt using metallic links.

The .50 BMG cartridge is also used in long-range target and anti-materiel rifles, as well as other .50-caliber machine guns.

A wide variety of ammunition is available, and the availability of match grade ammunition has increased the usefulness of .50 caliber rifles by allowing more accurate fire than lower quality rounds.

ER32 Collet Holder - Wall-Mount 3D-Printed Imperial SAE Standard Singles

Buy More Save More

All items in the "Mix&Match 3D Printed Singles" are eligible for this combined discount.

Enhanced Description

Upgrade your CNC or lathe workshop with the 3D Printed ER32 Collet Holder, a precision-engineered ER32 collet storage solution designed for maximum organization and protection. This wall mount ER32 holder features a custom-contoured cradle that securely fits ER32 collet chucks, preventing roll, wobble, or thread damage while keeping your tools elevated and free from dust and debris. The innovative tongue-and-groove stacking system—with a male half-round protrusion on the right and a female recess on the left—enables seamless side-by-side alignment, letting you build a stackable ER32 holder array for a clean, straight, and scalable wall-mounted setup.

Crafted from high-strength PLA+, this 3D printed collet organizer offers durability and lightweight portability, perfect for busy CNC shops or home machinists. The open-front design ensures quick access, while the reinforced four-point mounting system (including a critical center post screw) provides rock-solid stability—even with heavier loads. Whether you’re a professional or hobbyist, this ER32 collet wall mount transforms cluttered workspaces into an efficient, professional-grade environment.

Availability: Made to order with precision. Ships fast from Stadium Pen Blanks.

Critical Installation Instructions

For optimal performance and safety, secure the ER32 collet holder using two screws included with purchase. 

Pro Tip: When stacking multiple units, engage the tongue-and-groove system before final tightening to ensure perfect alignment and a polished look.

Key Features

• ER32-Specific Fit – Custom cradle prevents movement and protects threads
• Tongue-and-Groove Stacking – Male (right) + Female (left) connectors for modular alignment
• Wall or Bench Ready – Four-point mounting for versatile installation
• Thread-Safe Design – Elevated storage shields delicate collet threads
• Durable 3D Printing – Built with tough PLA+ for long-term use
• Space-Saving & Scalable – Create a clean row of CNC collet storage

Perfect For

• Machinists using ER32 collet storage systems
• CNC and lathe operators seeking wall mount collet holder solutions
• Workshop enthusiasts needing a 3D printed CNC organizer
• Anyone looking to protect collets from bench clutter or damage

Why Choose This ER32 Collet Holder?

Unlike traditional lathe collet holder designs, this stackable ER32 holder offers a modular approach, letting you expand your storage as your tool collection grows. Its 3D printed ER32 storage construction ensures a perfect fit and robust protection, making it a must-have for any CNC shop collet holder setup. Keep your ER32 collets aligned, accessible, and in top condition with this innovative modular ER32 collet rack.

Upgrade your workshop today! Order your ER32 collet organizer for wall from Stadium Pen Blanks and experience the difference in efficiency and organization.

#Hashtags: #ER32 #CNC #ColletHolder #3DPrinting #LatheTools #Bespoke #Kitless #KitlessPens #CustomPens #Standard #Imperial #SAE

ER32 Collet Holder - Wall-Mount 3D-Printed Metric Singles

Buy More Save More

All items in the "Mix&Match 3D Printed Singles" are eligible for this combined discount.

Enhanced Description

Upgrade your CNC or lathe workshop with the 3D Printed ER32 Collet Holder, a precision-engineered ER32 collet storage solution designed for maximum organization and protection. This wall mount ER32 holder features a custom-contoured cradle that securely fits ER32 collet chucks, preventing roll, wobble, or thread damage while keeping your tools elevated and free from dust and debris. The innovative tongue-and-groove stacking system—with a male half-round protrusion on the right and a female recess on the left—enables seamless side-by-side alignment, letting you build a stackable ER32 holder array for a clean, straight, and scalable wall-mounted setup.

Crafted from high-strength PLA+, this 3D printed collet organizer offers durability and lightweight portability, perfect for busy CNC shops or home machinists. The open-front design ensures quick access, while the reinforced four-point mounting system (including a critical center post screw) provides rock-solid stability—even with heavier loads. Whether you’re a professional or hobbyist, this ER32 collet wall mount transforms cluttered workspaces into an efficient, professional-grade environment.

Availability: Made to order with precision. Ships fast from Stadium Pen Blanks.

Critical Installation Instructions

For optimal performance and safety, secure the ER32 collet holder using two screws included with purchase. 

Pro Tip: When stacking multiple units, engage the tongue-and-groove system before final tightening to ensure perfect alignment and a polished look.

Key Features

• ER32-Specific Fit – Custom cradle prevents movement and protects threads
• Tongue-and-Groove Stacking – Male (right) + Female (left) connectors for modular alignment
• Wall or Bench Ready – Four-point mounting for versatile installation
• Thread-Safe Design – Elevated storage shields delicate collet threads
• Durable 3D Printing – Built with tough PLA+ for long-term use
• Space-Saving & Scalable – Create a clean row of CNC collet storage

Perfect For

• Machinists using ER32 collet storage systems
• CNC and lathe operators seeking wall mount collet holder solutions
• Workshop enthusiasts needing a 3D printed CNC organizer
• Anyone looking to protect collets from bench clutter or damage

Why Choose This ER32 Collet Holder?

Unlike traditional lathe collet holder designs, this stackable ER32 holder offers a modular approach, letting you expand your storage as your tool collection grows. Its 3D printed ER32 storage construction ensures a perfect fit and robust protection, making it a must-have for any CNC shop collet holder setup. Keep your ER32 collets aligned, accessible, and in top condition with this innovative modular ER32 collet rack.

Upgrade your workshop today! Order your ER32 collet organizer for wall from Stadium Pen Blanks and experience the difference in efficiency and organization.

#Hashtags: #ER32 #CNC #ColletHolder #3DPrinting #LatheTools #Bespoke #Kitless #KitlessPens #CustomPens #Metric