Maneater Crafts Products

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This model has overall dimensions of 4.5" sq x 3" tall with FOUR casting chambers, each measuring 2.5" tall x 1.5" round.  This will deliver blanks perfect for turning bottle stoppers and duck call bodies.  The blanks can easily be end trimmed and squared up on a table saw, if so desired. 

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This model has overall dimensions of 4.5" sq x 3" tall with SIX casting chambers, each measuring 2.5" tall x 1.5" round.  This will deliver blanks perfect for turning bottle stoppers and duck call bodies.  The blanks can easily be end trimmed and squared up on a table saw, if so desired. 

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Gator Mold Replacement Black Mushroom Plugs

Keep your Maneater HDPE casting molds performing at their best with these replacement black mushroom plugs. Designed specifically as direct replacements, the plugs restore proper sealing and alignment in your molds.

Large Plugs

Large plugs are ideal for the corners of most molds and the center positions in larger formats such as Gator block molds. Their robust construction ensures consistent pressure distribution during resin pours.

Small Plugs

Small plugs fit the slot positions in Dinobone molds and the corners of compact molds including Dogbone and Dual Socket Ring styles. They provide precise fitment for detailed pen blank casting.

These silicone plugs offer excellent chemical resistance and repeated-use durability. Pair them with your existing Maneater molds for reliable results every time.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack.  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out. These true beasts are designed to DEVOUR THE COMPETITION! 

 This model has overall dimensions of 7.25" x 6.75" x 1.25" with fourteen casting chambers, each measuring 1.25" round x .625" deep.  The blanks can easily be end trimmed and squared up on a table saw, if so desired. These ring molds are compatible for stacking directly with our 4 slot and 5" block molds.

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack.  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out. These true beasts are designed to DEVOUR THE COMPETITION!

This model has overall dimensions of 3.5" x 1.75" x 1.25" with two casting chambers, each measuring 1.25" round x .625" deep.  The blanks can easily be end trimmed and squared up on a table saw or bandsaw, if so desired.

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  And best of all, they stack!!  There is no need for a casting rack!  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out.  These true beasts are designed to DEVOUR THE COMPETITION!

This mold body has overall dimensions of 8.25" x 7.25" x 1.60" with four casting chambers, each measuring 1" x 1" x 6.0".  The blanks can easily be end trimmed and squared up on a table saw, if so desired.

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

5 oz of superb silicone mold release that is intended to be applied via brush.  The release agent works great with all Maneater molds, especially for epoxy resins which can be difficult to demold.

4 oz of superb wax based mold release that is intended to be applied via brush.  The release agent works great with all Maneater molds, especially for when casting with silicone inserts.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out. These true beasts are designed to DEVOUR THE COMPETITION!

This model has overall dimensions of 9.5" square x 2.25" with rounded corners and each of the four casting chambers measuring 4" round x 1.5" deep.  There is a single bonus short stopper mold in the center measuring 1.5" round x 1.625" deep. The blanks can easily be end trimmed on a table saw, if so desired.  

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Silicone or Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.

Introducing a brand new line of custom crafted molds that are sure to change the hand casting industry.  These are semi-permanent in nature.  They won't warp or crack but will take lots of abuse, unlike traditional silicone molds.  These tough molds are solid bodies, milled from blocks of HDPE (High Density Polyethylene).  Demolding is easy!  Just pull the suction plugs, turn the mold upside down, rap the ends a few times on your work bench and watch the blanks fall out. These true beasts are designed to DEVOUR THE COMPETITION!

This model has a casting chambers measuring 4" round x 1.5" deep. The blanks can easily be end trimmed on a table saw, if so desired.  

Important Notes:

A release agent must be used due to the rigidity of the molds.  Maneater Silicone or Wax Mold Release is highly recommended.  Just brush the release agent into the chambers, ensuring complete coverage.  Allow to dry before pouring your resin.  Also apply a release agent on the rubber plugs to keep them free of any resin buildup caused by potential spillage. 

A rubberized dead blow hammer will help the demold process greatly.  Lightly rap the bottom and sides of the mold once your blanks have fully cured, then turn the mold over and lightly rap the mold ends against your work bench top to see your blanks release.  Based on personal experience, Alumilite and polyester resin blanks will release with little effort at all.  Epoxy blanks may require a few extra raps or a blast of air from a rubberized nozzle before releasing.